FAQ Detail
| Select a search area | Enter a Keyword | Browse by area | |
|
|||
Synthesizer Workstations
Transpose, Note Shift and Tuning
The Pitch can be transposed for the entire unit (with or without drums being effected) or individually for each Part in a Performance. In addition, the pitch of individual elements within the voice can be tuned. While the following procedures do not address Song, Pattern or Mixing Voice mode operations, many of the concepts used here apply in those modes as well. Transpose: Global for the internal sounds and out via MIDI by half steps.1)
Press the [UTILITY] button.
2) Press the [F1] button.
3) Press the [SF2] button.
4) Cursor down to 'TRANSPOSE'.
5) Turn the (Data Dial) to transpose the pitch from -11 to +11 semitones (half-steps).
Reference: Owner's Manual, p.251
2) Press the [F1] button.
3) Press the [SF2] button.
4) Cursor down to 'TRANSPOSE'.
5) Turn the (Data Dial) to transpose the pitch from -11 to +11 semitones (half-steps).
Reference: Owner's Manual, p.251
Octave Transpose: global for the internal sounds and out via MIDI by octaves, drums will remain at normal pitch.
1)
Press the [UTILITY] button.
2) Press the [F1] button.
3) Press the [SF2] button.
4) Cursor to 'OCTAVE'.
5) Turn the (Data Dial) to transpose the pitch from -3 to +3 octaves.
Reference: Owner's Manual, p.251
2) Press the [F1] button.
3) Press the [SF2] button.
4) Cursor to 'OCTAVE'.
5) Turn the (Data Dial) to transpose the pitch from -3 to +3 octaves.
Reference: Owner's Manual, p.251
Note Shift: For the internal sounds only by half steps, drums will be pitched higher or lower.
1)
Press the [UTILITY] button.
2) Press the [F1] button.
3) Press the [SF1] button.
4) Cursor down to 'NOTE SHIFT'.
5) Turn the (Data Dial) to transpose the pitch from -24 to +24 semitones (half-steps).
Reference: Owner's Manual, p.250
2) Press the [F1] button.
3) Press the [SF1] button.
4) Cursor down to 'NOTE SHIFT'.
5) Turn the (Data Dial) to transpose the pitch from -24 to +24 semitones (half-steps).
Reference: Owner's Manual, p.250
Master Tune Adjust: For the internal sounds only, drums will be pitched higher or lower.
1)
Press the [UTILITY] button.
2) Press the [F1] button.
3) Press the [SF1] button.
4) Cursor down to 'TUNE'.
5) Turn the (Data Dial) to adjust the pitch from -102.4 to +102.3 (up or down ½ step).
Reference: Owner's Manual, p.250
2) Press the [F1] button.
3) Press the [SF1] button.
4) Cursor down to 'TUNE'.
5) Turn the (Data Dial) to adjust the pitch from -102.4 to +102.3 (up or down ½ step).
Reference: Owner's Manual, p.250
Using Note Shift on an Individual Voice with in a Performance: For the internal sounds only, the actual drum note assignments will change creating unusual drum combinations.
1)
Press the [PERFORM] button and select a Performance.
2) Press the [EDIT] button.
3) Press the Part [1] - [4] button.
4) Press the press the [F4] button.
5) Press the press the [SF1] button.
6) Cursor to Note Shift.
7) Turn the (Data Dial) to shift the Individual Part pitch from -24 to +24 semitones (half-steps).
NOTE: To keep this setting, the Performance must be stored to memory.
Reference: Owner's Manual, p.173
2) Press the [EDIT] button.
3) Press the Part [1] - [4] button.
4) Press the press the [F4] button.
5) Press the press the [SF1] button.
6) Cursor to Note Shift.
7) Turn the (Data Dial) to shift the Individual Part pitch from -24 to +24 semitones (half-steps).
NOTE: To keep this setting, the Performance must be stored to memory.
Reference: Owner's Manual, p.173
Detune an Individual Voice within a Performance: For the internal sounds only, drums will be pitched higher or lower.
1)
Press the [PERFORM] button and select a Performance.
2) Press the [EDIT] button.
3) Press the Part [1] - [4] button.
4) Press the press the [F4] button.
5) Press the press the [SF1] button.
6) Cursor to Detune.
7) Turn the (Data Dial) to shift the individual Voice pitch from -12.8 to +12.7 (up or down approximately ¼ tone).
NOTE: To keep this setting, the Performance must be stored to memory.
Reference: Owner's Manual, p.173
2) Press the [EDIT] button.
3) Press the Part [1] - [4] button.
4) Press the press the [F4] button.
5) Press the press the [SF1] button.
6) Cursor to Detune.
7) Turn the (Data Dial) to shift the individual Voice pitch from -12.8 to +12.7 (up or down approximately ¼ tone).
NOTE: To keep this setting, the Performance must be stored to memory.
Reference: Owner's Manual, p.173
Coarse Tuning an Element within an Individual Voice: For the internal sounds only. Press the [Voice] button and select a Performance.
1)
Press the [EDIT] button.
2) Press the Element [1] - [4] button.
3) Press the press the [F2] button.
4) Press the press the [SF1] button.
5) Cursor to Coarse.
6) Turn the (Data Dial) to shift the individual Voice pitch from -48 to +47 semitones (4 octaves).
NOTE: To keep this setting, the Voice must be stored to memory.
Reference: Owner's Manual, p.138
2) Press the Element [1] - [4] button.
3) Press the press the [F2] button.
4) Press the press the [SF1] button.
5) Cursor to Coarse.
6) Turn the (Data Dial) to shift the individual Voice pitch from -48 to +47 semitones (4 octaves).
NOTE: To keep this setting, the Voice must be stored to memory.
Reference: Owner's Manual, p.138
Fine Tuning an Element within an Individual Voice: For the internal sounds only.
1)
Press the [Voice] button and select a Performance.
2) Press the [EDIT] button.
3) Press the Element [1] - [4] button.
4) Press the press the [F2] button.
5) Press the press the [SF1] button.
6) Cursor to Fine.
7) Turn the (Data Dial) to shift the individual Voice pitch from -64 to +63 (up or down 1 semitone).
NOTE: To keep this setting, the Voice must be stored to memory.
Reference: Owner's Manual, p.138
2) Press the [EDIT] button.
3) Press the Element [1] - [4] button.
4) Press the press the [F2] button.
5) Press the press the [SF1] button.
6) Cursor to Fine.
7) Turn the (Data Dial) to shift the individual Voice pitch from -64 to +63 (up or down 1 semitone).
NOTE: To keep this setting, the Voice must be stored to memory.
Reference: Owner's Manual, p.138
