| |
|
|
XH200 featuring a 2-channel high-impedance power amplifier
(200W/24 ohms @70V, 200W/48 ohms @100V).
The current switching allows for a compact and lightweight
design (10kg). This series utilizes the newly developed 2U shell.
Highly precise dB display detented attenuators, dedicated to
each channel, are located on the front panel. The models also
feature a protection circuit that allows you to monitor its status
with an indicator. Attention to detail for better practicality can
be found wherever you look.
Equipped with XLR and Euro-block inputs and barrier strip
terminal outputs. Also equipped with monitor/remote terminals
and a subsonic filter. The models have been designed with all
sorts of usage in mind.
|
|
Specifications: | |
| General Specifications |
Power Output Level
20Hz 20kHz
THD+N=0.1% |
8Ω |
70V/channel RL=24. 200W x 2 |
4Ω |
70V/channel RL=24. 200W x 2 |
8Ω / BRIDGE |
100V/channel RL=48. 200W x 2 |
70V/BRIDGE
RL=16Ω |
100V/channel RL=48. 200W x 2 |
| Sensitivity |
RL=8. Att.max |
|
| S/N Ratio |
20Hz-20kHz(DIN AUDIO) |
|
| Idle Power Consumption |
40W |
| 1/8 Power Consumption (4Ω) |
250W |
| Power Bandwidth |
(Half
power THD+N=0.5%) |
10Hz – 40kHz |
| THD+N |
20Hz 20kHz,
half power |
0.1% |
| Intermodulation Distortion |
60Hz:
7kHz,
4:1, half power |
0.1% |
| Frequency Response |
f=20Hz-20kHz |
-0.5dB, 0dB, 0dB 80Hz-20kHz |
Channel
Separation |
Half
power RL=8Ω 1kHz
ATT. Max input 600Ω shunt |
60dB(24Ω) |
| Residual Noise |
20Hz-20kHz
(DIN AUDIO) |
–65dB |
| Damping Factor |
8Ω,
f=1kHz |
100 |
| Voltage Gain |
ATT.
max |
38dB(100V), 35dB(70V) |
| Maximum Input Voltage |
22dB |
Input
Impedance |
30kΩ (Balance) 15kΩ (Unbalance) |
| Controls |
Front panel |
POWER switch (push
on/push off), attenuator (31position) x 2 |
Rear panel |
MODE switch (70V/100V) x 1
HPF switch (40Hz/80Hz 12dB/oct) x 1 |
| Connectors |
Input |
euro-block (balance)/ch |
Output |
Barrier strip/ch |
DATA PORT |
D-sub15P, Monitor:Output Level/ch,Active/ch,
Model Detect Control:Mute/ch |
Power |
AC inlet x 1 |
| Indicators |
POWER |
x 1 (Green) |
SIGNAL |
x 2(Green) |
CLIP/LIMIT |
x 2 (Red) |
PROTECT/MUTE |
x 2 (Red) |
| Load Protection |
POWER switch on/off mute,
DC-fault output relay off |
| Amplifier Protection |
thermal (heatsink temp =
90°C), VI limiter(RL = 16Ω) |
| Limiter Circuit |
clip limiting,THD ≥ 1.0% |
Cooling/
Variable-speed fan |
stop-50C-variable-70C-Hi |
| Power Requirements |
UC: 120V / 60Hz, EU: 230V /
50Hz, A: 240V / 50Hz |
Dimensions
(W x H x D) |
480 x 88 x 412.2 mm
(18-7/8"
x 3-7/16" x 16-1/4") |
| Weight |
10kg (22 lbs.) |
|
|
