|
|
P2201
PA Power Stereo Amplifier
| Simplified Circuits | | Voltage amplifying stages (first stage and predrive stage) are all connected to the cascade for obtaining wide band, and Pc is distributed for improving reality. |
| NFB | | NFB is applied at the final stage of voltage amplifying to enable low distortion and high stability at a relatively low level of 40dB. |
| Input Circuit | | The input level control employs the metal-grazed volume having attenuation characteristics according to PC-50C of the BTS Code. The input impedance is designed in such a manner as to obtain 25K Ohms at its maximum value, and the required attenuation characteristics and impedance characteristics at a ATT load resistance of 100K Ohms. |
| Values of Capacitors | | Values of Capacitors C101(A) and C201(B) located at the inlet of the driver circuit board are determined with ultra-bass range and shock noise protection in mind when the power switch is on. When the values are small, the peak occurs at low frequency, while when the values are relatively large, rise of TR101 is delayed due to a charging time constant when the power switch is turned on. |
| Predrive Stage | | The Predrive Stage consists of transistors TR108, TR109(A), TR208, and TR209(B), being cascade connected. Fuse resistance is utilized for emitter resistance when determining gain and input impedance, thereby improving the safety factor of the Predrive Stage. |
| Output Stage | | The Output Stage, which is darlington-connected to the driver, is a triple push-pull complementary OCL system, using the high power transistor of Vceo=200V and Pc Max=150W. The output signal picked up at midpoint between the plus and minus terminals is delivered to the speakers through L101(A) and L201(B). |
| Power Supply Circuit | | The Power Supply transformer uses a toroidal iron core which is half the size and weight of the El type core with the same capacity, thus significantly reducing the size and weight. |
| Power Output Per Channel | 200 Watts into 8-ohms with less than 0.05% T.H.D. (Total Harmonic Distortion), over a bandwidth of 20Hz to 20kHz, both channels driven. 350 Watts into 4-ohms with less than 0.05% T.H.D., over a bandwidth of 20Hz to 20kHz, both channels driven. | | Frequency Characteristics | 10Hz - 100kHz, +0dB, -1dB. | | Total Harmonic Distortion (both channels driven) | Less than 0.01% at 100 Watts into 8-ohms, 20Hz to 20kHz. Less than 0.005% at 50 Watts into 8-ohms, 1kHz. Less than 0.01% at 150 Watts into 4-ohms, 20Hz to 20kHz. Less than 0.01% at 150 Watts into 4-ohms, 20Hz to 20kHz. Less than 0.005% at 50 Watts into 4-ohms, 1kHz. Less than 0.05% at 350 Watts into 4-ohms, 20Hz to 20kHz. | | Intermodulation Distortion | Less than 0.05% using frequencies of 70Hz and 7kHz mixed in a ratio of 4 to 1, ouput level of 28.2dBm into 4-ohms. (or 8-ohms). | | Damping Factor (8-ohms load) | Greater than 300 at 1kHz. | | Hum and Noise | At least 100dB Signal-to-Noise Ratio. | | Channel Separation | At least 70 dB at 20kHz. (L to R, R to L). | | Input Sensitivity | An input of 0dB, +/-0.5.dB will produce an output of 100 Watts into 8-ohms if the ATTENUATOR is set at a minimum attenuation (maximum level). | | Voltage Gain | 31.2dB (volume maximum). | | Input Impedance | 25K Ohms, unbalanced. | | Rated Voltage | 120V 50/60Hz | | Rated Power Consumption | 600W, 650VA | | Primary Fuse | T4.0A 125V x 2 | | Rated Voltage (US/C) | 120V 50/60Hz | | Rated Power Consumption (US/C) | 600W, 650VA | | Primary Fuse (US/C) | T7.0A 125V x 2 | | Ambient Temperature | -10 degrees Celsius to +50 degrees Celsius | | Dimensions | 19'' x 15'' x 7-1/5'', 480(w) x 376(d) mm x 183(h) | | Panel Size | 19'' x 7''480(w) x 176(h) mm | | Rack Mount | 19" standard rack mount attachable | | Weight | 19.5kg |
|
