02R96V2
02R96 Digital Mixing Console with V2 Software
 |
|
 |
||
 |
 Update
your Twitter Status...
Your Twitter Status has been successfully updated. Thanks for sharing 02R96V2 product Wrong Username/Email and password combination.. Please try again!  Enter
your Email information...
Your email has been successfully sent. Thanks for sharing 02R96V2 product Wrong Username/Email and password combination.. Please try again! |
|
||
|
||||
Facebook
Digg
MySpace
back to Share options
|
|||||||||||
| GENERAL SPECIFICATIONS | ||
| Number of scene memories | 99 | |
| Sampling Frequency | Internal External |
44.1kHz,
48kHz, 88.2kHz, 96kHz Normal rate 44.1kHz-10% - 48kHz+6% Double rate 88.2kHz-10% - 96kHz+6% |
| Signal
Delay (CH INPUT to STEREO OUT) |
Fs=48kHz Fs=96kHz |
=
1.9ms = 0.7ms |
| Fader | 100mm motorized with touch sense x 25 | |
| Fader
Resolution Master faders, Stereo fader |
+10--96,8-dB
(256 steps/100mm ) 0--130,8-db(256 steps/100mm) |
|
|
Total Harmonic Distortion *1 (CH INPUT to STEREO OUT) |
Input
Gain = Min. Fs=48(96)kHz |
=0.05%
20Hz to 20(40)kHz @+14dB into 600Ω =0.01% 1kHz @+18dB into 600Ω |
| Frequency
Response (CH INPUT to STEREO OUT) |
Fs=48kHz Fs=96kHz |
0.5,-1.5dB
20Hz - 20kHz @+4dB into 600Ω 0.5,-1.5dB 20Hz - 40kHz @+4dB into 600Ω |
| Dynamic
Range (maximum level to noise level) |
DA
Converter (STEREO OUT) AD+DA (to STEREO OUT) |
110dB typ., Fs=48 or 96kHz 105dB typ., Fs=48 or 96kHz |
| Hum
& Noise *2 (20Hz-20kHz) Rs=150Ω Input Gain=max. Input Pad=0dB Input Pad=0dB Input Sensitivity=-60dB |
-128dB
(EIN : Equivalent Input Noise) -92dB (Residual Output Noise) @STEREO OUT STEREO OUT off -92dB (96dB S/N) @STEREO OUT STEREO fader at nominal level and all CH INPUT faders at minimum level -64dB (68dB S/N) @STEREO OUT STEREO fader at nominal level and one CH INPUT fader at nominal level |
|
| Maximum Voltage Gain | 74
[48]dB from CH INPUT1-16 [17-24] to STEREO OUT/OMNI (BUS) OUT 74 [48]dB from CH INPUT1-16 [17-24] to OMNI (AUX) OUT (via pre input fader) 74 [48]dB from CH INPUT1-16 [17-24] to CONTROL ROOM MONITOR OUT (via STEREO bus) |
|
| *1
Total Harmonic Distortion is measured with a 6dB/octave filter @80kHz. *2 Hum & Noise are measured with a 6dB/ octave filter @12.7kHz equivalent to a 20kHz filter with infinite dB/octave attenuation. |
||
| Power Requirements |
Power Requirements U.S./Canada 120 V 200W 60Hz. |
|
| Dimensions |
Height
9.41"(13.85") (including the MB02R96) |
|
| Weight | 74.95 lbs | |
| Operating
free-air temperature range |
10-35°C | |
| Storage temperature range | -20-60°C | |
| Accessories | AC
Cable CD-ROM (Studio manager) |
|
| Options |
Digital audio interface card (MY8,MY4 series) PEAK METER BRIDGE: MB02R96 SIDE PANEL: SP02R96 |
|
| LIBRARIES | ||
| Effect libraries (EFFECT1-4) | Number of
factory presets Number of user libraries |
52
(EFFECT3-8 :44) 76 |
| Compressor libraries | Number of
factory presets Number of user libraries |
36 92 |
| Gate libraries | Number of
factory presets Number of user libraries |
4 124 |
| EQ libraries | Number of
factory presets Number of user libraries |
40 160 |
| Channel libraries | Number of
factory presets Number of user libraries |
2 127 |
| Surround Monitor libraries | Number of
factory presets Number of user libraries |
1 32 |
| Input patch libraries | Number of
factory presets Number of user libraries |
1 32 |
| Output patch libraries | Number of
factory presets Number of user libraries |
1 32 |
| Bus to stereo libraries | Number of
factory presets Number of user libraries |
1 32 |
| ANALOG INPUT CHARACTERISTICS | ||||||||
| Input Terminals |
Position | Actual Load Impe-dance |
For Use with Nominal |
Input Level | Connector in Console |
|||
| Pad sw |
Gain Trim |
Sensi-tivity *1 |
Nominal | Max before clip |
||||
| CH INPUT A/B 1-16 |
0dB | -60dB | 3kΩ | A:50-600 Lines B:600Ω Lines |
-70dB (0.245mV) |
-60dB (0.775mV) |
-46dB (3.88mV) |
A:XLR-3-31
type (Balanced) *2 B:Phone Jack (TRS) (Balanced) *3 |
| 26dB | -16 (+10)dB |
-26dB (38.8mV) | -16dB (0.123V) | -2dB (616mV) | ||||
| 0dB (775mV) | +10dB (2.45V) | +24dB (12.28V) | ||||||
| CH INPUT 17-24 |
-35dB | 4kΩ | 600Ω Lines |
-70dB (0.245mV) | -60dB (0.775mV) | -46dB (3.88mV) | Phone Jack (TRS) (Balanced) *3 | |
| +10dB | 0dB (775mV) | +10dB (2.45V) | +24dB (12.28V) | |||||
| CH INSERT in 1-16 |
10kΩ | 600Ω Lines |
-6dB (388mV) | +4dB (1.23 V) | +18dB (6.16V) | Phone Jack (Un-balanced) *4 | ||
| 2TR IN ANALOG 1(L,R) |
10kΩ | 600Ω Lines |
+4dB (1.23V) | +4dB (1.23 V) | +18dB (6.16V) | Phone Jack (TRS) (Balanced) *3 | ||
| 2TR IN ANALOG 2(L,R) |
10kΩ | 600Ω Lines |
-10dBV (0.316 V) | -10dBV (0.316 V) | +4dBV (1.58V) | RCA Pin Jack (Un-balanced) | ||
|
*1. Sensitivity is the lowest level that will produce
the nominal output level when the unit is set to maximum gain. (all
faders and level controls are maximum position.) *2. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD) *3. Phone jacks are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND) • In these specifications, when dB represents a specific voltage, 0dB is referenced to 0.775 Vrms. • For 2TR IN ANALOG 2 levels, 0dBV is referenced to 1.00 Vrms. • All AD converters are 24 bit linear, 128times oversampling. • +48V DC (phantom power) is supplied to CH INPUT (1-16) XLR type connectors via each individual switch. |
||||||||
| ANALOG OUTPUT CHARACTERISTICS | ||||||
| Output Terminals | Actual Source Impedance |
For Use With Nominal |
GAIN SW | Output Level | Connector in Console | |
| Nominal | Max before clip | |||||
| STEREO OUT (L,R) |
600KΩ |
10KΩ Lines |
- | -10dBV (0.316V) | +4dBV (1.58V) | RCA Pin Jack (Unbalanced) |
| 150Ω | 600KΩ Lines |
- | +4dB (1.23 V) | +18dB (6.16 V) |
XLR-3-32 type (Balanced) *1 |
|
| STUDIO MONITOR OUT (L,R) |
150kΩ | 10KΩ Lines |
- | +4dB (1.23 V) | +18dB (6.16 V) | Phone Jack (TRS) (Balanced) *2 |
| C-R MONITOR OUT (L,R) | 150kΩ | 600KΩ Lines |
- | +4dB (1.23 V) | +18dB (6.16 V) | Phone Jack (TRS) (Balanced) *2 |
| OMNI OUT 1-8 | 150Ω | 10KΩ Lines |
+18dB (defalt) | +4dB (1.23 V) | +18dB (6.16 V) | Phone Jack (TRS) (Balanced) *2 |
| +4dB (1.23V) | -10dB(0.245V) | +4dB (1.23V) | ||||
| CH INSERT OUT 1-16 | 600Ω | 10KΩ Lines |
- | +4dB (1.23 V) | +18dB (6.16 V) | Phone Jack (Unbalanced) *4 |
| PHONES | 100Ω | 8KΩ Lines |
- | 4mW | 25mW | Stereo
Phone Jack (TRS) (Unbalanced)*3 |
| 40KΩ Lines |
- | 12mW | 75mW | |||
|
*1. XLR-3-32 type connectors are balanced. (1=GND,
2=HOT, 3=COLD) *2. Phone jack are balanced. (Tip=HOT, Ring=COLD, Sleeve=GND) *3. PHONES stereo phone jack is unbalanced. (Tip=LEFT, Ring=RIGHT, Sleeve=GND) *4. CH INSERT IN/OUT phone jacks are unbalanced. (Tip=OUTPUT, Ring=INPUT, Sleeve=GND) • STEREO OUT [L, R], 0dBV is referenced to 1.00 Vrms. • In these specifications, when dB represents a specific voltage, 0dB is referenced to 0.775 Vrms. • All output (except INSERT OUT 1-16) DA converters are 24bit, 128times oversampling. |
| DIGITAL INPUT CHARACTERISTICS | |||||
| Terminal | Format | Data Length | Level | Connector in Console | |
|
2TR IN DIGITAL |
1 | AES/EBU | 24-BIT | RS422 | XLR-3-31 type (Balanced)*1 |
| 2 | IEC-60958 | 24-BIT | 0.5Vpp/75Ω | RCA Pin Jack | |
| 3 | IEC-60958 | 24-BIT | 0.5Vpp/75Ω | RCA Pin jack | |
| CASCADE IN | - | - | RS422 | D-SUB Half Pitch Connector 68P (Female) | |
| *1. XLR-3-31 type connectors are balanced. (1=GND, 2=HOT, 3=COLD) | |||||
Brochure
| Optional: | |
| ADD-ON EFFECTS | Yamaha introduces the unique and valuable effect programs specifically designed for the Digital Consoles. |
| Y96K | 96kHz plug-in DSP card |
| MY16-mLAN | 16-channel digital audio and MIDI interface on mLAN (IEEE1394) |
| MY8ADDA96 - NEW! | 8-Channel Analog I/O |
| MY8AD96 | 24-bit, 96 kHz eight-channel line-level analog input card (25-pin D-sub connector) |
| MY8DA96 | 24-bit, 96 kHz eight-channel analog output card (25-pin D-sub connector) |
| MY8AE96 | Eight-channel AES/EBU digital format I/O (25-pin D-sub connector) |
| MY8AE96S | Eight-channel AES/EBU digital format I/O with sample rate conversion. (25-pin D-sub connector) |
| MY8AE | Eight AES/EBU digital format I/O on a 25-pin D-Sub connector |
| MY8AT | Eight ADAT digital format I/O (optical connectors) |
| MY8TD | Eight TDIF digital format I/O (25-pin D-Sub connector) |
| MY8AD24 | Eight 24-bit analog inputs on balanced 1/4" connectors |
| MY4AD | Four 24-bit analog inputs on XLR connectors |
| MY4DA | Four 20-bit analog outputs on XLR connector |
| MY16AT | 16-channel ADAT format I/O |
| MY16AE | 16-channel AES/EBU format I/O |
| MY16TD | 16-channel TDIF format I/O |
| AP8DA | Eight Apogee 24-bit analog outputs (25-pin D-sub connector) |
| AP8AD | Eight Apogee 24-bit analog inputs (25-pin D-sub connector) |
| MB02R96 | Peak Meter Bridge |
| SP02R96 | Side Pad |
| Click here for guidance on the use of MY Series cards | |
