Search
Digital
DSP5D Digital Mixing System – NEW!  
LS9 Digital Mixing Consoles – NEW!  
DM2000 VCM  
M7CL Digital Mixing Console  
PM1DV2 Digital Audio Mixing System  
PM5D / PM5D-RH   
DM1000V2   
02R96V2  
01V96V2  
Analog
Rackmount
Powered
Audio Workstations
Commercial Audio   Products   Mixers   Digital   
OR
M7CL Digital Mixing Console
M7CL Digital Mixing ConsoleM7CL Digital Mixing Console for a mid-range live application. Available for 32 channels and 48 channels


Promo Video

Flashplayer 7 Required
Enlarge Picture
Features  Specifications  Accessories  Software  Downloads  Block Diagram  Dimensions  Panel Views  Brochure  
General Specifications
Sampling Frequency Internal: 44.1kHz, 48kHz
External: 44.1kHz (-10%) to 48kHz (+6%0)
Signal Delay Less than 2.5ms INPUT to Stereo A, B
(@ Sampling frequency = 48kHz)
Fader 100mm motorized x 62 (46)
Touch Screen LCD 800 x 600 dot TFT LCD
Total Harmonic Distortion* INPUT to STEREO A
Input Gain=Minimum, PAD=ON
Master fader at nominal level and
one input fader at nominal level		 Less than 0.05% 20Hz to 20kHz @+4dBu into 600Ω
Frequency Response
Input Gain=Max, PAD=Off
Master fader at nominal level and
one input fader at nominal level		 INPUT to STEREO A
0.5, -1.5dB 20Hz to 20kHz @+4dBu into 600Ω
Dynamic Range
Input Gain=Minimum, PAD=ON
Master fader at nominal level and
one input fader at nominal level		 110dB typ. DA Converter (STEREO A)
108dB typ. AD+DA (to STEREO A)
Hum & Noise**
Input Gain=Max, PAD=Off
Master fader at nominal level and
one input fader at nominal level		 -128dBu typ. Equivalent Input Noise
-86dBu residual output noise (STEREO A)
STEREO Master off
Maximum Voltage Gain 86dB INPUT1-48 to Each Output
Crosstalk (@1kHz) -80dB adjacent input channels
(INPUT1-48, ST IN 1-4[L, R], OMNI OUT 1-16)
Phantom Power 48V
Dimensions
(W x H x D mm)		 M7CL-32: 1,060 x 286 x 701 (Included MBM7CL: 340)
M7CL-48: 1,274 x 286 x 701 (Included MBM7CL: 340)
Net Weight M7CL-32: 42kg
M7CL-48: 50kg
Power Requirements AC100-240V 50Hz/60Hz
Power Consumption M7CL-32: 250W
M7CL-48: 300W
Operation free-air Temperature Range +10°C to +35°C
Storage Temperature Range -20°C to +60°C
* Total Harmonic Distortion is measured with a 18dB/octave filter @80kHz
** Hum & Noise is measured with 6dB/octave filter @ 12.7kHz; Equivalent to a 20kHz filter with infinite dB/octave attenuation.

Analog Input Characteristics
Input
Terminals		 GAIN Actual
Load
Impedance		 For Use
With
Nominal		 Input Level Connector
Sensitivity *1 Nominal Max. before
Clip
INPUT 1-32
<M7CL-32>
INPUT 1-48
<M7CL-48>		 -62dB 3kΩ 50-600Ω
Mics &
600Ω
Lines		 -82dBu (61.6µV) -62dBu (0.616mV) -42dBu (6.16mV) XLR-3-31 type
(Balanced) *2
+10dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
ST IN 1-4 [L, R] -62dB 3kΩ 50-600Ω
Mics &
600Ω
Lines		 -82DbU (61.6µV) -62dBu (0.616mV) -42dBu (6.16mV) XLR-3-31 type
(Balanced) *2
+10dB -10dBu (245mV) +10dBu (2.45V) +30dBu (24.5V)
TALKBACK -60dB 3kΩ 50-600Ω
Mics &
600Ω
Lines		 -70dBu (0.245mV) -60dBu (0.775mV) -40dBu (7.75mV) XLR-3-31 type
(Balanced) *2
-16dB -26dBu (38.8mV) -16dBu (0.123V) +4dBu (1.23V)
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum position.)
*2. XLR-3-31 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*3. In these specifications, 0dBu = 0.775 Vms.
*4. All input AD converters are 24bit linear, 128times oversampling.
*5. +48V DC (phantom power) is supplied to INPUT (1-48), ST IN 1L-4R, TALKBACK XLR type
connectors via each individual software controlled switches.

Analog Output Characteristics
Output Terminals Actual
Source Imp.		 For Use With Nominal GAIN
SW *5		 Output Level Connector
Nominal Max. Before Clip
OMNI OUT 1-16 75Ω 600Ω Lines +24dB (default) +4dBu (1.23 V) +24dBu (12.28 V) XLR-3-32 Type (Balanced) *1
+18dB -2dBu (616mV) +18dBu (6.16V)
PHONES 15Ω 8Ω Phones – 75mW *6 150mW Stereo Phone Jack (TRS) (Unbalanced) *2
40Ω Phones – 65mW *6 150mW
*1. XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)
*2. PHONES stereo phone jack is unbalanced. (Tip = LEFT, ring = RIGHT, Sleeve = GND)
*3. In these specifications, 0dBu = 0.775 V rms.
*4. All output DA converters are 24bit, 128times (@48kHz) oversampling.
*5. There are switches inside the body to preset the maximum output level.
*6. The position of the level control is 10dB lowered from Max.

Digital Output Characteristics
Terminal Format Data
Length		 Level Connector
2TR OUT DIGITAL AES/EBU *1 Professional Use 24bit *2 RS422 XLR-3-32 Type (Balanced) *3
*1. Channel status of 2TR OUT DIGITAL
*2. Dither: word length 16/20/24 bit
*3. XLR-3-32 type connectors are balanced. (1 = GND, 2 = HOT, 3 = COLD)

Control Input/Output Characteristics
Terminal Format Level Connector
MIDI IN MIDI – DIN Connector 5P
OUT MIDI – DIN Connector 5P
WORD CLOCK IN – TTL/75Ω Terminated BNC Connector
OUT – TTL/75Ω BNC Connector
REMOTE – RS422 D Sub Connector 9P (Male)
Ethernet Ethernet 100Base-T RJ-45
LAMP 1, [2] – 0V-12V XLR-4-31 type *1
USB USB 1.1 Host *5 USB* 6 A type USB Connector (Female)
DC POWER INPUT – – JL05 Connector
*1. 4pin = HOT, 3pin = COLD, lamp rated powered 5W Voltage can be adjust by a software.
All specifications are subject to change without notice.

Home | Products | News | Training | Locate a Dealer | Service & Support
Yamaha Corporation of America | About Yamaha | Careers | Warranty/Safety Information | Privacy Policy
© 2008 Yamaha Commercial Audio Systems, Inc. All rights reserved. Terms of Use and Copyright Notice